Reviews for Mountain Off-Road DPJL18DS Driver Side Dead Pedal for 18-21 Jeep Wrangler JL & Gladiator JT
Wrangler JL 4xe owners, read on.
I always check alignment of welded parts because they are not always aligned well. In this case it was not any different. There is a bracket with two welded threaded bolts that goes well into the Jeep bracket mentioned in the instructions but it was off by maybe 1.5 millimeters (around one-sixteenth of an inch) shy which forced me to have to drill the bolt hole the next size up. I could have returned it but I really like the dead pedal to rest my left foot on so I acquiesced and drilled. Shouldn't have to do this but chose my battle on that one. The installation is really not easy. I considered removing the drivers side seat which would have made the install a lot easier but I eventually got the thing installed. We have a 2021 4xe which in this case has a module installed on the bracket required to mount the dead pedal on. Not sure what it does but was really careful with it since I really didn't know what it was responsible for. After about 2 hours of wrestling with the install, a couple of zip ties for the module and a whole lot of sweat, I got the pedal installed. I am definitely pleased but I gave this a 4 star because of the drilling required and it doesn't take less than an hour. I feel that timeline is a little misleading but it sells the product.
****IMPORTANT NOTE**** - it is required that you set the pedal position before installation and if I had to do it all over again, and I am not, I would have set it the pedal on the first notch and not the second. I am 67 inches tall (5'7") with an inseam of 32" so my leg length is pretty normal for my height. It is just fine where it is at but I would have preferred the pedal a little close.
Hope this helps anyone reading this and maybe save them a little trouble along the way.
1st MORE product. Very happy with the construction of the pedal itself. Solid piece.
However, whomever was running the machine shop on the day my bracket was made should have a firm talking to. My bracket was too short. Not that it was too short for the holes in the Jeep, it was too short for the dead pedal itself. You can tell by the welds on the bolts that someone wasn't paying very close attention.
What should have been a 30 minute install turned into 3 hours of cutting and grinding to make it work.
Would have given it five stars, but I’m not 16, 100 lbs and a gymnast, lol. The whole thing is very robust but you have to be very careful not to lose the bracket with the welded bolts behind the Jeep frame or the washers and nuts as well. I put it through and then put one of the nuts on it in case it slipped, then taped it to the frame. Also, you have to find the right combination of socket and extension to not get in the way of the pedals. FYI, I’m 5’ 8” and should have probably put it in the closest (to the driver) position.
If I was six years old and left handed it would have been MUCH easier to install...but after severe bruising I got it installed (2 hours). The product will do the job I requested.
Thank you
Rock solid product quality - this thing is built like a tank - and corrects a horrible oversight/omission by Jeep. Hard to quantify how much this helps. Minus one star because the total install is waaaay harder than it needs to be. Keep in mind this is all done in a pretty awkward position. Placing the backer plate and front plate isn't difficult at all. However, the tolerances are SUPER tight (not necessarily a bad thing) so if you need to remove it to adjust where the pedal is, you're going to struggle a bit. It has no back and forth wiggle room and it's too tight to pull straight off. Just have to pry it a bit. Do-able, but not easy at all.
The real issue is where the nut that holds the pedal is located. Nearly impossible to thread on initially and it takes A LOT of tool manipulation to actually tighten it. This could and does need to be reconsidered and fixed from a design standpoint.
Again, super solid quality and once it's on, it's a dream. But desperately needs a little design re-think.
Bit of a pain to install, just be careful to not lose the bracket as you are trying to work it into the 2 holes. Tie a piece of fishing line or thread on it in case it falls into the void below. Once in place, use a piece of duct tape to keep it there!
Once in, looks awesome and feels great on the road!
Very rugged and high quality materials and finishing. Makes driving much more comfortable. It's a pain to install and the only way to adjust it is to completely remove and reinstall.
Tricky to install used some rope to hold bracket in place so I could install pedal. Has 3 different adjustment positions. Comes with a sticker instead of the word m.o.r.e. cut out off it.
This dead pedal is sturdy, but wow is it tough to get in and adjusted. Worse, i tried all 3 positions before settling on the middle. Each time i took it off the backing plate was bent and was a BEAR to get out. Have a flex extension with socket ready, really saves a lot of effort. I folded up a piece of cardboard to put behind the backing plate to hold it steady while putting the pedal in place and securing the nuts. Also, there is a wire that runs behind the jeep bracket, make sure you don't get it between the bracket and the backing plate. I like it now that the memory of contortions is fading!
A five star product that is ridiculously difficult to install. Solidly built but you need to be a contortionist to get everything in place. Do some online searching before you install - there are some useful tips that make it somewhat easier.